Split Taper Bushing

The tapered barrel on these bushings is split on both sides, allowing them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They’re for Split Taper Bushing china employ with split-tapered sprockets and pulleys of the same bushing design. As you tighten the included screws, the bushing grips the shaft and pulls it into the sprocket or pulley.
This Split Taper Bushing is designed exclusively for use with cast iron bushed bore pulleys and can be purchased on the same page as the pulley you will need. For work with with 5/8” shaft sizes. Includes set screws. Added Features: Manufactured from Steel For employ with cast iron bushed bore pulley
Our stock metal Split Taper bushings feature wrench torque capability from 95 to 3,000 pounds and bore sizes from 3/8″ to 6-3/16″.
The split tapered bushing is a flanged bushing. Split tapered bushings are used on sheaves, pulleys, sprockets and gear belt pulleys. The split tapered bushing alleviates the need to have a component bored to size, ideally lowering on hand requirements and enabling alterations in shaft size if important. The barrel of the split tapered bushing is normally split in two spots and is keyed to the shaft. The barrel OD is also keyed to the drive component aswell. The good thing about the split tapered bushing is it will hold, whether or not the fasteners become loose. Split tapered bushings will be interchangeable between manufacturers.

Taper bushing are widely used as well as sprockets, v-belt pulleys, timing pulleys, coupling and other mechanical parts with taper bore connections.
Taper bushing series are made of high quality engineered components with superb tolerance. The characteristic is easy to work with and needs no added alteration. These bushings can suit almost all types of assemblies and sizes. They will be the best choice in style for mechanical connections.
To complete designations put bore size. For instance: PD1215X16MM designates a 1215 taper bushing with a 16mm bore.
No costly re-boring: complete selection of both metric and imperial available.
Standard range fits up to 125mm/5″ shafts & Hub diameter required is determined by the application.
Complete brief reach range available, for compact lightweight assemblies & Clean, Compact Style.
Simple installation and removal.
This Split Taper Bushing is designed exclusively for use with cast iron bushed bore pulleys and may be purchased on a single page as the pulley you will need.
For use with 1 3/16” shaft sizes.
Includes 2 set screws.

Additional Features:
Made of Steel
For use with cast iron bushed bore pulley
This U1 Bushing with 5-1/2″ bore is a high-quality precision product that’s built for strength and strength. U1 bushings are being used in an extensively wide variety of applications, including; sprockets, shaves, pulleys, gears, and much more, we likewise offer all of these products. What units this bushing apart may be the high-quality steel construction along with precise manufacturing and high quality control; this means that you always get a premium quality regular product. What really models us apart from the other folks is our highly trained expert workers and our company-wide goal of customer satisfaction.
1. Be certain the tapered cone surfaces of the bushing and the inside of the driven product will be clean and free of anti-seize lubricants.
2. Place the bushing in sprocket or different part type that accepts the bushing.
3. Place cap screws loosely in pull-up holes. The bushing continues to be loose to make sure sliding suit on shaft.
4. With essential on shaft, slide the sprocket or other part type to the desired posture on the shaft. Make sure to keep the heads of the cap screws accessible.
5. Align the sprocket or part type, tighten the screws additionally and progressively until they happen to be pulled up tight. Do not work with extensions on the wrench handles , nor permit the sprocket or portion to become drawn i connection with flange of bushing. At this time there must be a gap between your bushing flange and sprocket, make sure this gap does not close.
Dual split barrel ensures concentricity
Grips the shaft with confident clamp fit
High torque carrying capacity
Permits blind assembly
Load not carried or limited by mounting screws
External key on most sizes for great drive and better torque carrying capabilities
Double-split barrel for great clamping
Solid flange to keep up concentric bores
Available in inches, metric, and spline bores. Bore range from 3/8″ to 10″
Solid Flange & Double Split Barrel – Assures better concentricity to the shaft.
Key to Key Travel – With keys upon both the shaft and merchandise to provide the strongest possible drive.
3/4″ per Foot Taper on Barrel – Personal locking taper supplies the highest degree of mechanical locking item to product.
The tapered barrel on these bushings is split on both sides, allowing them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They’re for use with split-tapered sprockets and pulleys of the same bushing design. As you tighten the included screws, the bushing grips the shaft and pulls it in to the sprocket or pulley.
This Split Taper Bushing is designed exclusively for use with cast iron bushed bore pulleys and may be purchased on a single page as the pulley you will need. For use with 5/8” shaft sizes. Comes with set screws. More Features: Made of Steel For employ with cast iron bushed bore pulley
Our stock steel Split Taper bushings feature wrench torque potential from 95 to 3,000 pounds and bore sizes from 3/8″ to 6-3/16″.
The split tapered bushing is a flanged bushing. Split tapered bushings are used on sheaves, pulleys, sprockets and equipment belt pulleys. The split tapered bushing alleviates the necessity to have an element bored to size, preferably lowering readily available requirements and allowing for adjustments in shaft size if important. The barrel of the split tapered bushing is normally split in two spots and is keyed to the shaft. The barrel OD can be keyed to the drive component aswell. The advantage of the split tapered bushing could it be will hold, regardless if the fasteners become loose. Split tapered bushings are interchangeable between manufacturers.