EP brand replacement gearbox for woods rotary gearbox

EP brand name alternative gearbox for woods rotary gearbox

NEW forty HP GEARBOX Clean Enter one three/8 12 spline output Interchangable with market place common size i.e.: OMNI GRIZZLEY CHEETAH HOWSE KING KUTTER BUSH HOG HICO SILVER EDGE Many A lot more

Features
(1) model new forty five horse electrical power shearpin gearbox. This gearbox suits several distinct helps make of 4′,5′ and some 6′ rotary cutters. I market a whole lot of these packing containers each 12 months for several various purposes and have ALL Substitute Parts for this box, but hopefully you will not have to worry about that.
Right here are the specs on the box:
*45 horse electricity gearbox
*Standard one-three/eight” smooth input shaft(exactly where the pto shaft hooks on). The pto shaft is held on by a 1/two shearbolt.
*duration of the enter shaft out of the gearbox is 3″ long
*bolt hole sample for mounting is on the corners, 4-3/4 heart of hole to middle of hole. It normally takes a 5/eight” bolt.
*twelve splined output shaft(exactly where the blade provider hooks up on the bottom)
*one-9/sixteen outside measurement more than the output shaft splines- from the base of the output cap to the stop of the splines is 2-three/4″ prolonged- all round size of the output shaft is four-1/2″ prolonged.
*will take a one” threaded castle nut and a carter key on the bottom of the output shaft to protected blade pan(NUT is incorporated – – BLADE PAN IS NOT!!)
*general top of the box from the prime of the mower deck to the prime of the box is nine-1/two”
This is a relatively large merchandise (47 lbs.) so freight is not cheap, but we do not make something off of freight, whatsoever ups charges us we charge you.
40 HP
one:one:47 Ratio
one-3/8″ Sleek Input Shaft with Shear Pin Hole
one-1/two” twelve-Spline Ouput Shaft
Bolt Sample: 6-one/2″ (4) five/eight” Holes, 5″ Heart Gap Necessary for Shaft Assembly
The Input and Output Shafts Can’t be Acquired Serparately.
They are Offered as a package.
The kit involves the adhering to areas: enter shaft, enter equipment, output shaft, output equipment.
The Shaft Kit Can’t Be Divided.

EP manufacturer substitution gearbox for woods rotary gearbox

Rotary Cutter Gearbox Troubleshooting Guide
Is your mower leaking, creaking or in any other case carrying out incorrectly? You’ve appear to the appropriate place.

Study below for the most frequent concerns with rotary cutter gearboxes and their answers (from rapid and filthy, to expert).

Leaking Base Seal:
If you’ve got wrapped some baling or fencing wire all around your output shaft and blown the seal, the skilled factor to do is to exchange the seal.
If your output seal is intact, and you are capable to get ID, OD and thickness measurements (in millimeters), most bearing properties can buy you up a generic double-lip seal that will get you again up-and-working. If not, give us a call and we can help you type out what you want.
A dental decide is the best way to get rid of the aged seal before urgent in the new a single.
If you are fortunate ample to have a slow-leak, the fast and filthy technique is to operate automotive-kind grease in the gearbox until finally the new seal will come in. Be positive to examine and incorporate grease far more usually than you would with oil, as this is NOT a expert mend.

Broken Output Shaft:
Uh oh. You hit something that did not shift. The very good news is that the output shaft on most gearboxes is fairly simple to exchange. The poor news is… it is not often an isolated failure.
The first factor to do is to get apart your gearbox and assess the entire extent of the hurt. If it is actually just the output shaft, you should be capable to modify it out, no difficulty. The output shafts begin at about $70 and go up in price tag dependent on the dimensions of the gearbox.
Even so, in most situations, the bearings ($twenty/ea), seals ($10/ea) and equipment-set ($70) will also usually take a beating. If you might be unlucky, the output cap ($80) will also experience some damage.
In this situation, it is usually cheaper to exchange the gearbox. Evaluate the price of components to the expense of an total, new, warrantied gearbox. At times, even pros have to know when to get in touch with it a working day.

I Want to Alter my Input Shaft:
If you are drained of shifting shear pins or looking back and observing that your mower hasn’t been reducing, you could want to set up a slip-clutch pto shaft (Indeed, we offer those also).
This typically needs setting up a 540-type, 6-spline enter shaft ($85) on your mower’s gearbox.
Fortunate for you, we did a publish-up on our website. It is called “How to alter the input shaft on your rotary cutter gearbox”.

My Gearbox is Groaning/Creaking:
“Groaning”, “creaking”, or “popping” all sound type-of similar in excess of-the-phone. The greatest issue to do is to disassemble your gearbox and just take a look at the gears and bearings. The issue will generally present by itself in the way of damaged/lacking gear teeth, toasted gears (like that photo on our residence page), or blown bearings.
If everything appears typical, try modifying the gear-mesh. This is accomplished with the mylar “gaskets” that sit in between the major gearbox scenario and the input/output caps. Consider including or taking away some of these spacers until your gears have around 1/8″-1/four” of totally free enjoy. Experts can get replacements ($one-two) in different thicknesses, but we recommend the fast and filthy approach of chopping your own out of a sheet of mylar.
Don’t overlook to re-seal the gearbox with RTV right after you have identified the proper mix. Even however they’re referred to as “gaskets”, they will not likely seal your gearbox on their very own.

The makers of Gearbox geared motors For Horticulture Drive Systems located on the web site of http://hzpt.com/indgea.html based this idea on enhancing the lives of others.